How Stuff Works – Floatants

One of the worst things you can do to a dry fly is catch a fish on it!  They slime it and submerge it and swim it around… Just in general, keeping a dry fly floating better and longer seems to be an ongoing quest for many fly tyers and fishers.

There are a number of factors that can go into how well and how long a dry fly continues to float high. Certainly the materials from which the fly is tied will play a big role, as will the skill of the angler.  The more you allow your fly to drag across currents, rather than drift on them, the more waterlogged your fly will become. Where you are fishing will make a difference, too.  It’s easier to keep a fly floating high in big, open rivers where false casting is an option than it is in a small, tight mountain stream.  In any case, there are an endless number of products on the market that are designed to help with this task and we lump them all into the category of “floatants.”

As with many products in the fly fishing world, if you ask ten different anglers which one is the best, it’s entirely possible that you will get ten different answers. Sometimes those answers will come in the form of a specific brand of floatant, and others will come in the form of a specific style.  When it comes to brand, I believe that is a matter of personal preference and you’ll just have to try a few different ones to see if one in particular earns your loyalty.  But when it comes to different styles of floatant, the specific task at hand may determine which will be best.  In fact, you may want to have more than one style of floatant to perform different tasks. Listed below are a few different common styles of floatant and a description of how and when they might best be applied.

Liquid Floatants
While many anglers use them in different ways, liquid floatants are probably most useful before you ever get to the stream.  Whether dry flies that you tie yourself or buy from a shop, you can use a liquid style floatant to “pre-treat” new flies in much the same way as you might “Scotchgard” your sofa.  Exact application may vary and you should read the recommendations for the specific brand you purchase, but typically, flies will be soaked in the liquid for five minutes or so and then set out to dry overnight.  In theory, after application of the product, water will better bead and roll of the fly material rather than absorb into it.

Gel Floatants
Gel floatants are probably the most common and popular style of floatant.  They come in a small, very portable bottle and, like the liquid floatants, are designed to be a pre-treatment to an already dry fly.  The big difference is gel floatants are designed to be used streamside, immediately before fishing the fly.

It is important that gels are not “over applied.”  A small amount should be rubbed into the fly and any excess should be removed.  Gels are also frequently mis-applied – after a fly has already become waterlogged.  If a fly is already saturated, applying a gel floatant will essentially trap moisture into the fly and make it worse.

 

Spray Floatants
Also normally applied while the fly is still dry, spray floatants are basically just a variation on a gel floatant.  Spray floatants come in a bottle with a pump top and are applied much like you would spray something like an eyeglass cleaner.  They are not as messy as the gel but are sometimes more challenging to completey coat the fly.

 

Paste Floatants
These are basically just a thicker version of a gel floatant.  They can really create a mess on smaller dry flies and are probably best suited for larger dries like hoppers and stoneflies.  A lot of people prefer a paste floatant to apply to yarn strike indicators or even on a leader to keep it floating better.

 

 

Powder Floatants
These are used less as a pre-treatment and more as a means to revive a saturated fly.  As mentioned above, when a dry fly becomes oversaturated and begins to sink, applying a gel or spray can often make it worse by trapping moisture in.  Powder floatants are used to absorb and remove that moisture from a fly.

Typically they will come in a bottle with a wide, flip-top lid.  The fly, still attached to the tippet, is inserted into the bottle and the lid is closed.  The bottle is then shaken a few times and the moisture is removed from the fly.

At this point, there is a lot of debate on whether to re-apply a gel or spray type floatant and you’ll just have to find what works best for you.  I usually don’t re-apply another floatant unless I’m using a synthetic (like foam) dry fly.

Brush Floatants
Brush floatants are essentially another version of a powder floatant.  Rather than shaking the fly inside the bottle, a small brush is used to apply the powder to the fly.  Again, it’s personal preference but with brush floatants, be prepared for a little frustration on windy days!

 

 

There are countless styles and floatants on the market today and all have their place.  And unlike the homemade lighter fluid and paraffin concoctions of days gone by, they are typically odorless and environmentally friendly.  You just need to find a system that suits your needs.

Personally, I carry a gel floatant for pre-treating dry flies and a “shake style” powder for reviving them and get by just fine.  But I offer the disclaimer that I often offer in these newsletter articles… This is just one man’s opinion!

How Stuff Works: Forceps

In the world of fly fishing, there is an endless array of gadgets designed to serve every purpose from threading a fly, to removing a fly from a tree, to tying knots… If you have any task to perform in fly fishing that you find the least bit frustrating or unpleasant, chances are someone has invented a gadget to make it easier.  But I’ve never been much of a gadget guy and I try to keep the number of items I carry on the stream to a minimum.

It’s funny how different folks have different priorities when it comes to what they carry with them.  For instance, I never go into the backcountry without a daypack that includes a first-aid kit and the basic necessities (fire source, water purification, etc.) to spend the night if I have to.  While 99.9% of backcountry fishing trips go off without a hitch, there are a number of things that could go wrong, and I like to be prepared for the unexpected.  I was taught long ago that there is a name for people who go into the woods unprepared: “Statistics.”  Yet, I regularly encounter fishermen deep in the backcountry with no such provisions, but they will have fifteen different knot tying tools hanging from their vest!

I’ve taken a really long way around the barn to say that there are only two fishing “tools” that I routinely carry with me when I’m fishing: nippers and forceps.  I’ve talked about nippers in another article.  They are responsible for most of the work I’m doing with my line.  Forceps handle pretty much everything else.

If you get in certain circles, mainly the medical community, someone might correct you and say, “Those aren’t forceps.  They’re hemostats.”  Another might refer to them as clamps.  Maybe there are subtle differences in the three – I don’t know.  But in fly fishing, the three terms are interchangeable and refer to a tool that looks kind of like a pair of scissors but with a nose more like a pair of pliers.  While they come in slightly different shapes and sizes, most are fairly long and narrow and have a locking feature.

Forceps have a number of different uses but I mostly use them to perform three common tasks.  If I need to crimp the barb on a hook, whether required by law or simply preferred, I use my forceps.  If I need to squeeze a split shot on a leader, I use my forceps.  And if I happen to hook a fish a little deeper in the mouth and the fly is difficult to reach without harming the fish, I use my forceps.

The locking feature is most often used for hook extraction.  I clamp the forceps on the hook and carefully remove it from the mouth of the fish.  I also use the locking feature to clamp the forceps to my pack or shirt when they’re not in use.  For these reasons, I greatly prefer a pair of locking forceps to pliers.

Common “Medical Forceps”

I also prefer to have forceps with flat jaws.  Many forceps that might be offered to you by your friend who works in the ER will have grooved jaws.  Those grooved jaws are great for many of the intended tasks in medical applications, but they can be a hindrance when trying to crimp the barb on a hook.  Trout hooks are often so little that they work themselves into those grooves making it difficult to meet the barb with enough metal to flatten it.

The other downside to forceps that are made for the medical community is quality.  I know, it seems strange that a fly fisherman’s forceps would be superior quality to a doctor’s.  But medical forceps are often designed to be “single use,” so the metal used to construct them is inferior.  They bend and rust easily.  Forceps built for fly fishing are usually made of high quality stainless steel and built to last.  And assuming you don’t lose them, they should last forever.

Beyond that, the only real differences in fly fishing forceps are shape, color, and features.  Some are designed with a variety of add-ons, such as scissor blades, which would be great for anglers who might use yarn for strike indicators.  Color is sort of personal preference but there are also practical considerations.

Trout Skin Forceps

When fishing for spookier trout like those in the Smokies, I prefer not to have the bright silver or gold forceps because I think they “flash” too much when the sun hits them, potentially spooking trout.  But flat black ones are sometimes difficult to locate when you inevitably drop them in the water.  I’m a fan of the the “trout skin” colored forceps.  Not only are the cool looking, but they’re dull enough not to reflect much light, yet light enough to see in the water.

As always, a lot of it boils down to how you’re going to carry them, what they will be used for and your own personal preference for appearance. In any case, pick up a pair if you don’t have some already.  You’ll use them a lot.

How Stuff Works: Tippet Rings

Over the last few years, tippet rings have been gaining more and more popularity and acceptance.  Most new fly fishermen love them.  Most traditionalists hate them.  What are they?

In case you’re new to the sport, lets start with a quick overview of leaders.  The leader is simply the monofilament connection between the the heavier fly line and the actual fly. Typically 7 1/2′ to 12′ in total length, leaders are tapered from a thick butt section that attaches to the fly line to a finer tippet section that attaches to the fly.  Check out this link for more detailed info on leaders and tippet.

As you change flies (or lose them in trees), your tippet gets gradually shorter until it is no longer the proper length, or worse, you’ve cut it away to the point that you’re in the thicker part of the leader.  In this situation, you would cut a length of tippet from the appropriate size spool of tippet material, tie it to the existing leader, and ultimately rebuild your leader back to its original length and size.

Though tying the knot to splice the new piece of tippet back to the leader is not very complicated with a little practice, many anglers struggle with it, or don’t want to take the time to learn it.  For these fishermen, the tippet ring is like an answered prayer!

Varying sizes of tippet rings

Tippet rings are very small metal rings, available in a few different sizes, that simplify this splice.  You tie it to the end of your leader using whatever knot you prefer for tying on a fly.  Then you tie a piece of tippet to the ring using that same knot.  You could also tie a second piece of tippet off the ring to add a second fly for a dropper rig.  So, all of your frequent connections can be made using the same knot.

Multiple tippet rings are stored on a clip and for convenience, are often threaded and attached before removing from the clip

This is one of the biggest benefits to using tippet rings.  It just simplifies the process, particularly for someone who may not fish frequently and may have trouble remembering or executing various knots.  Another benefit is that they can greatly prolong the life of your overall leader since your always replacing tippet off the ring and not cutting part of your leader away every time you change tippet.

Of course, there are also down sides – at least in my opinion.  First, I don’t think it makes as strong of a connection as when you splice using more traditional Surgeons or Blood Knots.  This may not make much difference on smaller fish, but I believe you have a much better chance of breaking off a big fish if you’re using a tippet ring.  Second, the tippet ring creates a “dead spot” in the leader which can negatively impact you in a couple of ways.

One way is with straight line nymphing.  This technique is commonly used in mountain streams and requires a certain amount of feel.  With that tippet ring creating a dead spot between leader and tippet, I believe you’re more likely to miss some of the more subtle takes of a trout.  That dead spot also can create problems with accuracy.

One of the main functions of a tapered leader is to transfer energy during a cast.  It’s what helps prevent things like hard splash downs or tippet pile-up on a cast.  When you put a tippet ring in the middle of all of that, the dead spot created can act almost like a short in an electrical current.  The energy doesn’t transfer smoothly from the taper of the leader to the tippet and can create a hinging effect – resulting in a significant loss of accuracy.

Like most things, you have to consider the kind of fishing you do and how important things like feel or accuracy are to you.  For me, they’re pretty important.  For others, they may take a backseat to convenience.  And that’s okay!  Figure out your system and roll with it!

Keeping Your Dry Fly Floating High

A buoyant Humpy dry fly

In April, dry fly fishing really starts to turn on in the Smokies. Not only are there a significant number of hatches, but water temperatures are getting ideal and fish are just looking up, even when no hatches are present. Presenting a dry fly that rides high on the water, not only tends to produce more strikes, it is much easier for you to see. Here are a few tips to keep your fly floating high in the fast moving currents of the Smoky Mountains.

First off, if you don’t tie your own flies, be sure buy high quality dry flies. It can be tempting to find Internet companies or box stores that offer really cheap prices on flies, but they are cheap for a reason. These dry flies often have less hackle and/or use a very low-grade hackle, and they are simply not going to float as well. Bushy, heavily hackled flies will float the best, as will flies that utilize foam and/or deer hair. These are all great for most of the riffles and pocket water you encounter in the Smokies. However, if you’re fishing to slow water risers in a slick pool, you may want to use a more slender, low profile fly like a parachute or comparadun pattern.

Treat your flies before you fish them. There are a number of great products on the market that accomplish this and are generically referred to as fly floatant. The most common are silicone based and have a gel consistency. Just squeeze a drop on your finger and rub it into your fly. Orvis, Aquel, Loon and Gink are probably the most common brands. They’re all probably about the same but everyone seems to have their favorite. I use Orvis Hy-Flote.

Fly Floatant

Once you’ve selected your high quality dry fly and gooped it up with fly floatant, the worst thing you can do to it is catch a fish! They take it under water and slime it up to the point where it doesn’t want to float as well, especially after you catch 2 or 3 fish. When this happens, a mistake a lot of anglers make is to re-apply the same gel floatant they used to pre-treat the fly. However, you’re often just trapping moisture in to the fly at this point. You need to remove as much of the moisture from the fly as possible.

On bigger rivers such as tailwaters, your false cast can keep a lot of moisture out of the fly, even after several fish. But in places like the Smokies, frequent false casting is often not an option due to the tighter quarters, and is often not desired because of the increased risk of spooking fish. There are a number of methods I use to dry a saturated fly in these environments.

Dry Shake

One is to press the fly against an absorbent material. Amadou is a material sold at many fly shops that works great for this. You can carry a patch on your vest or pack and just squeeze the fly in it. Chamois cloth is another good option. If you’re in a pinch and don’t have either, just press the fly against your shirt. After employing this method, blow on your fly. Finally, consider carrying a second, powder based floatation product. These are desiccants, similar to what’s found in the small, “do not eat” pouches packaged with some clothing and electronics. Again, there are numerous brands. Frog’s Fanny is a favorite of many anglers. My favorite is Shimazaki Dry-Shake. It has a large-mouthed bottle that allows you to drop the fly in while still attached to the tippet. Close the lid, shake vigorously and remove. It will be floating like new.

The final tip for keeping that fly floating high is technique. What causes flies to get waterlogged more than anything else, especially with novice anglers, is drag. When your fly doesn’t drift naturally with the current, and instead pulls unnaturally against the current, not only will you not catch many fish, your fly is going to become more waterlogged and require far more maintenance to keep it floating.

Think about what you’re doing. Instead of dragging the fly through the run 2 or 3 times before making a good drift, read the water. Identify the varied currents that will pull your line at a different speed than the fly and try to position yourself where you can eliminate them. If you can’t eliminate them through position, think about how, when, and which direction you’ll need to mend BEFORE you make the first cast. And pick your fly up when it reaches the end of the target area, rather than letting it drift (drag) into the fast shallow riffle at the bottom of the run.

Keeping the line off the current lip at the rear of the pool provides a drag free drift through the sweet spot

Experienced anglers often do most of this instinctively, so it looks like they’re just casually moving around casting. The good ones always make it looks easy! If you’re newer to fly fishing or even if you’ve done it awhile but only get out a few times a year, it won’t be instinctive and you’ll have to think about it. This is just good advice, period. If you execute a good cast and drift in the right place the first time, you’ll not only keep your fly floating better, you’ll catch more fish!

Finally, on a similar note, carry your fly in your hand when you move from spot to spot. I see a lot of people who will let their fly drag behind them in the water as they wade up to the next pocket or run. If you do this, the best-case scenario is that you’re going to waterlog your dry fly. More often than not, you’re also going to hang your fly up on every rock and stick in the river!

How Stuff Works: Stripping Baskets

Plastic Stripping Basket

When you’re doing any type of fly fishing that involves stripping in great amounts of line after each cast, keeping that slack line under control can be a challenge. In streams and rivers, it’s usually not too big of a problem because the line will usually rest neatly in the water by your side. In a boat that is not equipped with some sort of stripping deck, it can be a little bit of a problem as your line wants to snag and tangle on absolutely everything in the boat. The biggest challenge is surf fishing because the constant rushing approach and retreat of the tide repeatedly wraps this slack line around your legs.

Mesh Stripping Basket

Stripping baskets are designed to solve this problem. I’ve seen larger, freestanding stripping baskets used in boats. But the most common stripping baskets are smaller and are worn around your waste. After you cast and you’re retrieving line, you simply strip and feed the line into the basket. They are basically just a bin with a series of upright “posts.” The posts help prevent the line from tangling inside the basket. There are also baskets made of mesh, but many note that these are often not durable.

Stripping baskets are pretty simple devices that have been around for decades, and they can be purchased from most fly fishing suppliers. If you don’t want to fork over $40-$90 for a plastic tub on a belt, you can also make your own. I did and it works great.

Start with a hard plastic bin like you find in the storage sections at Wal-mart, Home Depot, etc. It should be approximately 16”x 11” and about 5 or 6” deep. You’re also going to need a drill, a sander, some zip ties, wire cutters, and a bungee cord. The bungee cord will be used to secure the bin around your waist, so the length needed will be dependent on your size. You want it to be tight enough to keep the bin from falling off you but not so tight that it’s digging the bin into you.

Bottom View of Homemade Stripping Basket

Begin by drilling approximately ten 3/32” holes in the bottom of the bin near the edges. These will serve as drain holes for your stripping basket to keep water from accumulating inside. Next drill nine 3/32” holes spread equally in the middle of the bin. And drill another nine 3/32” holes right next to the ones you just drilled. These will serve as attachment points for your zip ties (the zip ties will act as the “posts” inside the box that help keep your line from tangling). Finally, drill two larger, approximately 3/16” holes (big enough to accept the hooks on your bungee) on the front of the bin, one near each top corner. This is where your bungee cord will attach. With light sand paper, smooth the front and back of each hole you drilled.

Interior View of Homemade Stripping Basket

Next, attach nine 4” zip ties through the “double holes” you created in the bottom of the bin, allowing the end of the zip tie to point upward into the interior of the bin. With your wire cutters, snip the tips off each zip tie so that you’re left with a 2” post that stands at an approximate right angle from the base of the bin. Hook one end of the bungee into one of the larger front holes. Bring the bungee around your waist and hook the other end into the second hole. I actually use two shorter bungees because I think it’s easier to attach and detach. You’re ready to go fishing!

Where you position the basket is a matter of preference. I typically see them positioned on the front of the body, but I prefer to wear mine closer to my left hip so I can feed line into the basket with a more natural stripping motion. I always use it when surf fishing and very frequently when I’m fishing from the canoe.

How Stuff Works: Strike Indicators

There seems to be few things in the fly fishing world that provoke as much debate as strike indicators. The mere existence of strike indicators in the sport of fly fishing can inspire rants from fly fishing purists that rival any political rant of that friend you just hid from your Facebook feed. But even among the firmly pro indicator crowd, nymphers will argue fiercely about the superiority of one type of indicator over another.

For newbies to the sport, a strike indicator is something that is often used while fishing with nymphs (sub surface flies). It is a brightly colored, floating object that is affixed to the leader intended to give the fisherman a visual indication when the fish hits his submerged fly, or nymph. Since the nymph usually can’t be seen under the water, and since it is usually fished with a slack line to achieve a dead drift, the strike can be difficult to detect without the visual aid of a strike indicator. Strike indicators can also be helpful in making sure the nymph is drifting properly (without drag) and at the desired depth.

The obvious question usually arises when hearing this description, “Isn’t that just a bobber?” Pardon the bobber pun, but that opens a whole other can of worms. There are a number of fly fishermen who will stop just short of taking a swing at you if you call a strike indicator a bobber. I assume this animosity stems from the association of bobbers with bait fishermen and fishing live bait; and fly fishermen don’t like to think anything they do might resemble bait fishing. So they call them strike indicators. The truth is that while strike indicators are typically smaller, lighter, and made from different materials than bobbers, they pretty much accomplish the same thing.

I use the term strike indicator because I think there is enough of a difference to specify, kind of like I don’t refer to a hamburger as a sandwich. It’s just different enough. But I won’t be offended if you call a hamburger a sandwich and it won’t offend me if you call a strike indicator a bobber!

Getting re-focused specifically on strike indicators, there are a lot of different kinds, and that’s what I want to focus on here. As mentioned before, most fly fishermen have their favorites, and a lot about selecting strike indicators will boil down to

personal preference. I personally don’t think there is such a thing as the perfect strike indicator. They all have pros and cons and I use different ones for different situations. Often I don’t use one at all, but that’s a topic for another article. Below is a list of some of the more common or popular strike indicators with a description of how they work and some of their strengths and weaknesses.

Hard Toothpick Indicators: These are usually made of cork, or balsa, or something similar. They are typically round or oval with a hole drilled in the center. The leader/tippet is inserted through the hole and the indicator may be moved to any position on the leader. Once the desired position is determined, the provided “toothpick” is inserted into the hole to hold the indicator in place.

These are great because they are buoyant, highly visible, reusable, and can easily be adjusted up and down the line to set the nymph at different depths. However, they tend to make more disturbance when they land on the water and can spook more skittish fish. Additionally, their mass makes them difficult to cast when placed on the tippet portion of the leader for shallow nymphing, though smaller ones can be purchased. They are best for deep to mid-depth nymphing and for quick and easy depth adjustment.

Hard Rubber Band Indicators: These are typically oval in shape and made from the same materials as the hard toothpick type indicators. Instead of having a hole and a toothpick, they have a slit that contains athick rubber band. The leader is inserted into the slit and the indicator is then rotated, allowing the rubber band to twist around the leader to hold the indicator in place.

They have pretty much the same pros and cons as the toothpick indicators. One additional advantage is they can be added or removed while the fly is still attached. However, they have a tendency to kink the leader when twisted on, and they come off the line more easily than other indicators when casting.

Thingamabobber

Balloon Style Indicators: The best known versions of these are the Thingamabobber and Air Lock. These are basically small, plastic balloons. They float great, are highly visible, and can be easily adjusted. They are particularly good if you need an indicator that will suspend larger, heavier flies. The Thingamaboober attaches by looping the leader through a hole and around the indicator. The Air Lock has a slot in the base where the leader is inserted and a separate piece that screws on to hold the indicator in place.

 

Air Lock

Much like the other hard indicators, when this indicator is set in the tippet section of the leader for shallow nymphing, it is difficult to cast and can create more tangles. It also lands hard on the water. It is more durable and floats better than the other hard indicators.

 

 

Stick-On Indicators: These are small round or oval pieces of foam that peel off and stick on to the leader. Their greatest value is that they cast easily, even when placed on the tippet and they make very little commotion on the water. So they are a great indicator for shallow nymphing. They float great and multiple indicators can be added to the line to support more weight.

The biggest downside to these is they are not reusable and they are not easily adjusted. When moved they lose a lot of their stick and then have a tendency to slide down the leader. They can usually be moved a few times before you have to trash them. Some complain that they also leave a sticky residue on the leader but I haven’t found that to be a problem.

Yarn Indicators: These are made from a buoyant yarn that is often pre-treated with a waterproofing agent, but floatant may also be added. There are a number of different versions of yarn indicators, but most attach by using some sort of slip knot or loop knot. Like the stick-ons, yarn can be attached to the tippet end of the leader without the worry of a hard landing or a lot of tangles. So this is another good choice for shallow nymphing. Yarn indicators are also very sensitive, so they are great for detecting subtle strikes.

On the downside, I find them difficult to add and remove from the line and when removed, they regularly leave kinks in the line. Larger yarn indicators can be wind resistant and difficult to cast in tight places and they require a little more maintenance to keep them floating.

Putty Indicators: Strike putty comes in a small tub and resembles Play-Doh. You pull out a small gob or big gob depending on how big you want your indicator to be, and you smoosh and roll it on your leader. One of the benefits it that you can smoosh more on if you need more flotation for bigger, heavier flies, or you can pick some off for smaller flies and spookier fish.

I’m trying to be impartial here but I don’t like this stuff. It always comes off, especially in warm weather. It leaves a permanent indicator-colored smudge on your line when you remove it. Finally, every bit of dirt in the vicinity attaches to it, so what starts as orange strike putty soon becomes and greyish, brownish, greenish, orange strike putty.

Dry Fly: In the right situations, a dry fly can serve as an edible strike indicator by adding a nymph “dropper” to it. For many, this is the go-to method because you’re essentially doubling your chances… or so it might seem. Just like any other strike indicator, a dry fly has its pros and cons.

Obviously, one of the big perks is that you have the potential to catch a fish on the nymph or the indicator, since the indicator is a fly. However, most dry flies don’t have near the buoyancy as an actual strike indicator, so if you’re needing to get heavier nymphs near the bottom of a deeper run, the dry fly will routinely get dragged under. In such a scenario, you’re not fishing the dry fly or the nymph very well, and hardly doubling your chances.

The best scenario for fishing a dry fly with a dropper is when you don’t need to get your nymph very deep, and you can fish a dry fly buoyant enough to support the nymph’s weight. I immediately think of pocket water. Another scenario might be in flatter water during a hatch, where you could put a nymph with little to no weight behind a dry fly to suggest an emerger.

The takeaway from all of this should be that there is not one strike indicator that is going to be perfect for every situation. You will likely need a variety to meet a variety of conditions. As with most things, much of it will boil down to personal preference and you should play around with a few different types to find what best meets your needs.

How Stuff Works: Landing Nets

Variety of Landing Nets

Landing nets are designed to enable anglers to land a fish more easily and safely. They are most beneficial when dealing with larger fish that have a tendency to make one last dart or head shake when you try to grab them, often resulting in the tippet breaking. While in the Smokies, I rarely carry a net because the fish are typically not very large and can be landed by hand with very little trouble, and a net is just one more thing to carry. But I use a net regularly when fishing tailwaters and delayed harvest streams.

Long Handle Carbon Net

Traditionally, nets have been made with a wood frame and cotton netting and that style is still common today. However, wooden frames are more and more frequently being replaced by lighter, carbon frames and rubber is replacing cotton for the netting. The rubber netting has a number of advantages over cotton – the most notable being that it is better on the fish. Cotton netting has a tendency to get caught and tangled in the fins, gills and teeth of the fish and with trout, absorbs and removes some of their protective “slime.” Fly hooks also catch and easily tangle in cotton netting. Rubber netting eliminates all of these problems and holds far less odor than cotton.

Other things to consider when looking for a net are the size and shape. Obviously, if you’re expecting to catch bigger fish you’re going to want a bigger net. A 20-pound striper just won’t fit in a 16 ½” trout net. Landing nets are typically sized by the overall length, including handle, as well as the size of the head (the part that holds the netting). The size of the head should be chosen based on the size of fish you’re pursuing while the overall length (or the handle size) should be chosen based on how you will be pursuing them. For instance, if fishing from a boat, a longer handle may be desirable since it’s more difficult to get the fish close to you. If wading, a long handled net might be too cumbersome to carry all day.

Magnetic Net Holder

If you plan to carry a net with you when wading, there are a number of options that will help keep the net out of the way, yet easy to access when needed. Most every fishing vest or jacket has a D-Ring on the back. The sole purpose of that ring is to clip your net on it. To make it even easier, there are magnetic connectors that include a section of plastic, “pig tail” type cord that allow you to utilize the net while it remains tethered to you. There are also oversized retractors that accomplish the same thing.

Net Holster

Folks who choose to use sling packs or hip packs tend to have trouble finding a suitable location for attaching their net. Attaching it to the pack with a traditional retractor or magnetic connector often leaves it hanging too low or in a location that impedes the casting stroke. I know many who have remedied this by using a type of net “holster” placed on a belt. The net is stored handle down and drawn from the holster when needed.

Like most things in fly fishing, there doesn’t seem to be a “one size fits all” solution to the type of net you use or the method you use to carry it. It’s a matter of finding something that best fits most of your needs and carrying it in the least obtrusive way possible.

Dressing For Success

One of the Easiest Ways to Catch More Trout in the Smokies….

I recently guided a husband and wife on a small brook trout stream in the Smokies. The stream, like most in the Smokies, consisted of a lot of pocket water, which meant getting closer to the fish. Both were novice fly fishers and their skills improved steadily as the day went on. As a matter of fact, their skills were about equal, but as the day progressed the wife was getting 5 or 6 strikes for every 1 strike the husband got.

 

We were moving up the stream together and they were taking turns fishing. They were fishing the same fly. And as mentioned before, their casting ability, approach, and presentation was nearly identical. What was different, you ask? The wife was wearing a drab green shirt and the husband’s shirt was bright red. Simple as that.

 

Look how this white shirt stands out

Casting can be challenging. Getting good drifts can be challenging. Figuring out what the fish are eating can be challenging. But dressing appropriately is one of the easiest things to control and can greatly improve your success on the stream.

 

Now look how well this fisherman blends in

Years ago, three seasoned fishermen from Montana walked into Little River Outfitters frustrated that they had fished two days without catching a fish. One was wearing a bright blue shirt, another was wearing a white shirt, and the other’s shirt was bright coral color. My good friend, Walter Babb, was sitting in the shop and without pulling any punches, said, “Well, those fish saw you guys get out of the car!”

When the fishermen pointed out that they wore the same clothing in Montana and caught plenty of fish, Walter went on to explain that in big western rivers, your background is the sky. Here it’s the trees and bushes.

This is a bit extreme!

You don’t have to be a fly fishing commando decked out in camouflage and twigs in your hat to catch fish in small mountain streams, but dressing in earth-tone colors does make a huge difference. Think drab greens, browns, tans, and greys when you dress for a day on the water. While bright white t-shirts and orange Tennessee ball caps may be appropriate for game day at Neyland Stadium, they are doing you no favors on the trout stream.

 

What about strike indicators? They’re bright and colorful. Don’t they spook fish? Sometimes they do, but usually for different reasons. It’s not really the bright color that spooks fish; it’s movement. These are wild trout in the Smokies and they’re right in the middle of the food chain. Any kind of movement, particularly above them, often means a kingfisher or heron is about to swoop down and eat them! The less you blend in to your background, the more pronounced your silhouette is, and the more noticeable your movements are.

The cone

All of this becomes more and more important the closer you have to get to the fish, even when you’re behind them. Trout actually have a “cone of vision” above them that even extends a little bit behind them. The closer you get and the higher up you are, the more you will be detected in that cone. So in addition to what you wear, think about how you move through the water to reduce the chances of spooking fish. Move slowly and quietly. Stay low, particularly when fishing in close quarters. See that big boulder in the stream? Don’t fish from on top of it. Stand behind it.

 

Finally, keep your false casting to a minimum. Fly lines are often brighter colors so that you can see them in order to mend and achieve good drifts. Remember, it’s not the color so much as the movement. Repeatedly false casting a fly line over a trout’s head is excessive movement in that cone of vision and will send him under a rock.

Nippers

It’s Time to Quit Using Your Teeth….

Welcome to the wonderful world of nippers! It’s probably pretty easy to figure out that the primary function of nippers (aka clippers, cutters, snips, etc.) is to cut your line. They are mostly used to trim the tag ends of monofilament after tying a knot or to cut a new piece of tippet from a spool. But as you’ll see, the right pair of nippers can perform a number of other tasks as well.

As I have described before, my beginnings in this sport were humble at best and my funds were rather limited. There was a lot I could do with $10 back then and I certainly didn’t want to waste it on nippers – not when I could just use fingernail clippers. That strategy served me well for a time, until I figured out what a lot of fishermen eventually figure out. First, fingernail clippers are made of very cheap, soft metal, and after repeatedly clipping monofilament line, they begin forming a series of nicks in the blade. It’s not long before they become completely useless. Second, when regularly exposed to water (such as every time you go fishing), they rust – quickly.

So you can constantly replace in expensive fingernail clippers or you can do what I ultimately did – drop $10 on a decent pair of nippers. They’re rustproof and will last years before the blades begin wearing out. The other benefit to a good pair of nippers is they are designed to cut line, not fingernails. What does that mean?

When working with smaller trout flies, particularly dry flies, it can be difficult to prevent the large, curved head of generic fingernail clippers from also clipping away some of the hackle. The straight, somewhat recessed blades on fly fishing nippers are designed work and cut in tight spaces. Most nippers designed for fly fishing also include another simple but highly useful feature – a small needle.

When a fly tyer finishes a fly, thread is knotted near the hook eye and coated with a thin, invisible cement. Well, in the world of fly tying, time is money and production fly tyers apply that cement quickly, often leaving an invisible layer in the hook eye. When it comes time for you to tie that fly on your line, you can’t get the tippet through the hook eye because it’s coated in glue. This happens even more frequently with hard-bodied poppers that might be dipped in paint, only it’s the paint that is coating the hook eye. The little needle on your

nippers is designed to clear that layer of cement or paint and preserve your sanity when attempting to attach a fly.

As with most any fly fishing product these days, there are seemingly endless nipper styles and features to suit your needs and tastes. Some are just shaped differently, boasting a better ergonomic design. Others are equipped with additional tools for tasks such as tying knots or sharpening hooks. And if you want to take it to the next level, check out this description of Abel’s nippers:

  • Designed, manufactured and assembled in the USA
  • Anodized 6061-T6 aluminum body construction
  • Replaceable jaws – machined out of premium grade Crucible CPM S35VN stainlesssteel, then heat treated to 58-60rc
  • Engineered to cut 7X – 100 lb mono and braid
  • Two Year limited warranty on the jaws after initial purchase
  • Pin – 316 stainless steelAnd they can be yours in black for a mere $85. For custom colors, they’re just $105. And with a cool fish print… a steal at $165. Yep, $165 for line cutters. All of a sudden, $10 for a pair of nippers doesn’t sound too bad, does it? As with anything else, if you have the disposable income and want to spend $165 of it on nippers, go ahead. I won’t judge you.